HSSI to V.35 CONVERTER |
V.35 cable &
V.35 cable gender mender
M/34 to M/34 and V.35-M/34 cable to DB25
ARC Electronics
jump to ... Home Page
CALL US FOR ALL YOUR V.35 Cable/CONVERTER NEEDS
301-924-7400 EXT 25
V.35 to HSSI Interface Converter Convert V.35 to HighSpeed Serial Interface (HSSI) at speeds up to 10
Mbps. |
Key Features for the
Model 2040, V.35 to
HSSI
Bi-Drictional Converter
Transparent to protocol Passes data, control lines, Two loopback modes. Built-in 6-ft. cable. Up to 10 Mbps CCITT V35 & HSSI V35 DTE to HSSI DCE, or V35 DCE to HSSI DTE HSSI co-directional timing |
Technically Speaking
HSSI (High-Speed Serial Interface) devices can now bi-directionally communicate with V35 devices at speeds up to 10 Mbps. The V35- HSSI Interface Converter supports all HSSI co-directional timing patterns, two loopback modes (local line and remote line), plus data and control signals.
Two versions of the Interface Converter are available. The 2040MT/MC lets a V.35 DTE device communicate with a HSSI DCE device. The 2040MC/MT lets a V.35 DCE device communicate with a HSSI DTE device. Both versions are equipped with a male M/34 connector on the converter end, and a male HD-50 on the end of a 6 foot (1.8m) cable (other connector genders and cable lengths are available on a custom basis). Power is supplied to the Model 2040 by an external AC transformer
Both STANDARD versions are equipped with a male M/34 connector on the converter end, and a male HD50 on the end of a 6-foot (1.8-m) cable. Power is supplied by an external AC power supply.
Application part number
from Communications V.35 DCE device to HSSI DTE data device. | M/34 DTE/HD50 DCE |
2040MT-MC/UI |
from Communications HSSI DCE device to V.35 DTE data device. | M/34 DCE to HD50 DTE (Male M/34 to male HD50) (an optional female M/34 or HD50 is available) |
2040MC-MT/UI |
NOTE:
When selecting converters a DTE must connect to a DCE or a DCE must
connect to a DTE.
If you have a CSU V.35 to a Router HSSI - the CSU will be DCE (which will connect to the
connverter DTE) and the router will be a DTE (which will connect to the connverter
DCE)
The Model 2040MC-MT is designed to connect a V.35 or RS-422 DTE device to an HSSI DCE device. In this application, the M/34 (V.35) and HD-50 (HSSI) male connectors of the Model 2040MC-MT may connect directly to their respective equipment ports, or they may connect via a short "straight-through" cable. Figure 7 below Illustrates the proper connection of the Model 2040MC-MT.
The Model 2040MT-MC is designed to connect a V.35 or RS-422* DCE device to an HSSI DTE device. In this application, the M/34 (V.35) and HD-50 (HSSI) male connectors of the Model 2040MT-MC may connect directly to their respective equipment ports, or they may connect via a short "straight-through" cable. Figure 8 below illustrates the proper connection of the Model 2040MT-MC.
Specifications
Data Rate - Up to 10 Mbps
Protocol - Synchronous Standards - CCITT V35; ITSSI (ANSI/TIA/EIA613)
Clocking - All modes supported except conversion from smooth to gapped clock
Loopbacks - Local and remote; Local DTE not available
Cable - 6 ft.
Interfaces - V35 DTE to HSSI DCE, or V35 DCE to HSSI DTE Connectors - HD50 Slimline and male M/34 male Temperature Range -32 to 122F (0 to 50C) Maximum Altitude - Up to 15,000 feet Humidity - 5 to 95%, noncondensing Power Supply - 100 to 240 VAC auto-sensing external power supply Size - 0.75"H x 1.75"W x 3"D (1.9 x 4.4 x 7.6 cm)