Telenetics MIU202T/MIU202TLV Modem

 HARDENED Bell 202T & V.23 4 WIRE LEASED LINE modem
Telenetics MIU202T modem - 48 to 220 Volts AC or DC Power
Telenetics MIU202TLV modem - 9 to 36  Volts DC Power
Telenetics MIU202Tpowerport modem - 5 or 12  Volts DC Power
(Bell standard 202T and V.23)
 

The Telenetics MIU-202T modem can be powered from a wide range of AC and DC voltages, is surge protected on both the power and telephone lines and will operate in extreme heat and cold. Ideal for both point-to-point and multi-drop applications over leased lines and private lines.

Telenetics has designed modems that work in "remote" remote sites with very low failure rates. These devices work where other modems roll over and die. When a service call to a remote site can mean an all day trip these modems are the ideal solution.

Bell 202T continues to be the standard of choice in many utility and industrial applications. The Telenetics MIU202T can be powered from a wide range of AC and DC voltages, is surge protected on both the power and telephone lines and will operate in extreme heat and cold. Ideal for both point-to-point and multi-drop applications over leased lines and private lines.

jump to MIU02T manual PDF file        get acrobat.gif (712 bytes)      

The MIU202T MIU202TLV and MIUPowerPort202T modems

The Telenetics MIU202T modem and MIUPowerPort202T are a Bell Standard 202T modems designed for asynchronous operation at 0 to 1800bps with C2 line conditioning, or 0 to 1200bps on unconditioned lines.

With the flip of a switch, the 202T can be configured for V.23 applications if required.

The modem is intended for use on leased lines and private lines and provides half duplex communications on 2-wire lines, or full duplex communications on 4-wire lines.

Most modem manufacturers have abandoned Bell 202 in favor of the much higher speed modulations preferred in dial-up systems. However, Bell 202 remains the standard of choice in many utility and industrial applications where relatively small amounts of data are to be transmitted point-to-point or in multidrop networks.

The MIU202T version can be powered from any AC or DC voltage in the range 9V to 220V AC/DC  The MIUPowerPort202T has 9 to 12V power supply.  The 202T  is designed to work in extended temperatures ranging from -40oC to +85oC, and is surge protected to 8kV, double the voltage requirements of IEC801-4 Standard.

All of this is bundled in a 5-3/8" x 4" x 1-3/8" package, suitable for desktop or wall mounting. Rack mount cards are also available.

MIU202T MIU202TLV MIUPowerport modem Technical Specifications

Power Supply:
MIU202T 48 to 220 Volts AC or DC
Power Consumption:
15mA @ 48VDC;
7.5mA @ 115VAC;
7.5mA @ 125VDC

 Operating Environment:
-40oC to +85oC, 0 to 95%
humidity (non-condensing)
MIUPowerPort  9 to 12 Volts AC or DC

MIU202T-LV 9 to 36 VDC

Power Consumption:
71mA @ 12VDC
65mA @ 12VDC		 Data Rate: (for both)
0 to 1200bps on Unconditioned Lines
Digital Port:  RS232
MIU        Female DB9 Connector
PowerPort -  DB25		 Analog Port: RJ11
Power Connector:
MIU has 3-Pin with Screw Terminals
PowerPort has 5.5mmX2.0mm plug		 Case Size:
5-3/8" x 4" x 1-3/8"
Surge Protection 
(Power Line):
8kV [Exceeds IEC801-4]		 Surge Protection
(Analog Line)
3.75kVac
Data Rate: Asynchronous

0 to 1200bps on Unconditioned Lines
Modulation

Bell 202 and V.23 (Dip Switch Selectable)
Phase Coherent, Frequency Shift Keyed (FSK)
Operation:

Full Duplex Over 4-Wire Leased or Private Lines
Half Duplex Over 2-Wire Leased or Private Lines
(Constant or Switched Carrier, Dip Switch Selectable)
Carrier Frequencies:
Mark: 1200 Hz ± 0.1%
Space: 2200Hz ± 0.1% 		Test Features:
Analog Loopback
Line Impedance:
600 ohms		 Antistreaming:
0 or 45 seconds
Transmitter Output Level:
0 or -10dBm		 Receive Sensitivity:
-33 or -42dBm
RTS/CTS Delay:
1, 16, 35 or 51msec		 Carrier Detect Delay:
15msec
Soft Carrier Turnoff:
0 or 8.3msec

 

for OEM module see PE-202T-OEM

 

ARC ELECTRONICS
 301-924-7400 EXT 25

jump to ... Home Page

 arc@arcelect.com